3D-LF-ANALYSER WITH DATA LOGGER NFA1000
3D-LF-ANALYSER WITH DATA LOGGER NFA1000

The NFA1000 is the top model of the NFA meters. Of course, all unique features of the NFA series are implemented.

  • Frequency range: 5 Hz to 1000 KHz (compensated)
    • Also includes modern power adapter radiation reducible to 400 KHz for TCO measurements
kr 20 990 Add to my Cart
Utleie  av HF Analyzer  HF 35C (per uke)
Utleie av HF Analyzer HF 35C (per uke)

HF/RF-Analyzer HF35C
for the easy HF evaluation, incl. Audio Analysis

This is THE device for technical amateurs – especially easy to operate. It supports all above mentioned «common advantages» and it allows a straight forward assessment of the exposure, a determination of suitable remedial actions, as well as a control of their effectiveness.

Has the same features and configuration as the HF32D, however additionally offers

* Audio Analyses for the identification of pulsed radiation sources (mobile radio (GSM, UMTS/G3), cordless telephones (DECT), WLAN (Bluetooth), air-traffic control-radar) by means of an acoustic signal proportional to the modulation frequency
* Display of peak value as well as average value (switchable)
* Sensitivity increased by a factor of 10 (from a minimum display resolution of 0.1µW/m² to a maximum of 1999 µW/m²)
* HINT: Our best-selling meter for the easy evaluation!
* Technical Data

Frequency Range: 800 MHz – 2.5 GHz
Measurement Range: Power flux density: 0.1 – 1999 uW/m²
Accuracy: Basic accuracy including linearity tolerance : +/- 6dB
Zero offset and rollover +/- 9 digits
Sensor: Logarithmic periodic antenna
Audio Analysis: Identification of pulsed radiation sources (mobile radio (GSM, UMTS/G3), cordless telephones (DECT), WLAN (Bluetooth), air-traffic control-radar) by means of an acoustic signal proportional to the modulation frequency
Stromversorgung: 9 Volt Alkaline manganese battery (included)
avarage operation time 6 – 7 hours
Low Batt. Indication
Auto-power-off
Signal Rating: Display of peak value as well as average value (switchable)
Further Questions: 2 years warranty
Weight: 480 g#
RF-Analyser HF35C
for an easy HF evaluation, incl. audio analysis.

This is THE device for technical amateurs – especially easy to operate. It supports all above mentioned «common advantages» and it allows a straight forward assessment of the exposure, a

kr 600 Add to my Cart
Utleie av BaJog NA02-13 skittenstrømmåler
Utleie av BaJog NA02-13 skittenstrømmåler

Utleie av håndholdt nettverksanalysator for skittenstrøm.

kr 800 Add to my Cart
Utleie av DG20 Dempningsledd
Utleie av DG20 Dempningsledd

#
Attenuator DG20
suitable for: HF32D, HF35C, HF38B

Allows a measurement of major exposures.

For high exposures

* Reduces the sensitivity of the measuring device by a factor of 100 (= 20 dB).
* Adaptor plug to be connected to the antenna input socket.

kr 150 Add to my Cart
Utleie av DG20_G10 Dempningsledd
Utleie av DG20_G10 Dempningsledd

#
Attenuator with DC-Bypass DG20_G10
suitable for: HFE35C, HF58B, HF58B-r, HF59B, HFE59B

For the measurement of major exposures.

In addition to all features of the DG20:

* enhanced frequency linearity and DC-bypass.

kr 200 Add to my Cart
Utleie av Easy-Gamma Mini Geigerteller, per uke
Utleie av Easy-Gamma Mini Geigerteller, per uke

LF-Analyser ME3851A for professional LF analysis This device represents the low cost access to the professional, quantitative low frequencymeasurement technology. It is suitable for measurement certificates, comprises all features of the ME3840B, LF-Analyser ME3851A
for professional LF analysis

This device represents the low cost access to the professional, quantitative low frequencymeasurement technology. It is suitable for measurement certificates,

comprises all features of the ME3840B, however additionally offers:

* Responsivity increased by a factor of 10 (display range: 0.1 V/m to 0.1 nT)
* A NiMH battery, a battery charger and a power supply unit inclusive
* An AC- and a DC-output
* Increased reliability by the use of a test switching mode for the zero deviation
* Perfectly suitable also for potential-free measurements with the help of the potentialfree mounting for LF measurement devices

* Technical Data

Frequency Range: 5 Hz bis 100 KHz (compensated, better than -2 dB).
Measurement Range: 1-2000 nT V/m
0,1-200 nT V/m
Accuracy: precision : +/- 2 %, +/- 7 digits
Sensor: E-Fieldsensor for electrical LF- fields
H-Fieldsensor for magnetic LF-fields
Audio Analysis: An acoustic signal proportional to the field strength with ? Geiger-counter-effect? helps
identifying regions with increased exposure.
Stromversorgung: recharchable NiMH battery inside the meter
Outputs: AC- and a DC-output
Further Questions: 2 years warranty
Weight: 1050 g

kr 700 Add to my Cart
Utleie av FF6 E Frekvensfilter til alle HF (HF 35 oppover)
Utleie av FF6 E Frekvensfilter til alle HF (HF 35 oppover)

FF6 er et lav- høy- og bånpass filter anbefalt for HF E 35C og HF E 59B. Med dette filteret er det enkelt å finne hvilke strålingskilder som er dominerende. Ved hjelp av en glidebryter velger du den kilden du er interessert i (f. eks. DECT) og avlese

kr 1 000 Add to my Cart
Utleie av FF6 E Frekvensfilter til alle HF (HF 35 oppover)
Utleie av FF6 E Frekvensfilter til alle HF (HF 35 oppover)

FF6 er et lav- høy- og bånpass filter anbefalt for HF E 35C og HF E 59B. Med dette filteret er det enkelt å finne hvilke strålingskilder som er dominerende. Ved hjelp av en glidebryter velger du den kilden du er interessert i (f. eks. DECT) og avlese#
Service-specific frequency filter FF6E
Recommended for: HF E 35C, HF E 59B.

The service specific filters always only show the preset radio service, and suppress all other frequencies.

Evaluates each radio service separately
Additional features as compared to the FF6:

* The 50-60 dB suppression of unwanted frequencies is unequalled in this product segment. It allows for a precise analysis of the selected frequency ranges.
* With its additional filters for TETRA-BOS, DVB-T, as well as high and low pass combinations applied at 1100 MHz this filter is especially suited for our E-type measuring devices (as from 27 MHz).
* To be connected between the antenna cable and the antenna input socket of the measuring device (by the operator).
* Cascadable with all amplifiers and attenuators.
* Also allows for a broadband measurement without additional transmission loss, which means the filter can remain attached to the device.
* Perfectly shielded against interferences.
* Possible exposures to sheath currents on the cable behind the filter can be additionally suppressed with the help of a free of charge modification of your HF-device.

Add to Cart

* filter
* Rg58 coaxial cable
* tightening aid
* manual
* charger

* Technical Data
* Scope of Delivery
*

Frequency Range: ALL / GSM9 / GSM18 / DECT / UMTS / WLAN / HP11/ TP11 /TETRA / DVB-T
Accuracy: Typical suppression of unwanted frequencies: > 50-60 dB, GSM1800 vs. DECT eff. 20-30 dB.
Electric power supply: 9 V NiMH battery, average time of operation: 8 hours, Low-Batt. indication, auto-power-off-function, mains adaptor, battery charger

kr 1 000 Add to my Cart
Utleie av HF Analyzer  HF 32 D (per uke)
Utleie av HF Analyzer HF 32 D (per uke)

HF/RF-Analyzer HF32D
for the easy evaluation of the HF exposure

This is the device for technical amateurs – especially easy to operate. It allows a straight forward assessment of the exposure, a determination of suitable remedial actions, as well as a control of their effectiveness.

Already this starter device has all common advantages and yet it is equipped with all of the above mentioned «common features» – the only one of ist kind in this price category

* Reading shows the total pollution without any calculation required
* The measured values are reliably displayed directly in the entity corresponding to the building biology standard values, namely
* Digital display of 1 µW/m² up to 1999 µW/m².
* An acoustic signal proportional to the field strength with «Geiger-counter-effect» helps identifying regions with increased exposure.
* Measurement device
Attachable log.-per. antenna incl. Cable
Alkaline Mangan battery
Detailed instruction manual with factual background information
* Technical Data

Frequency Range: 800 MHz – 2.5 GHz
Measurement Range: Power flux density: 1 – 1999 uW/m²
Accuracy: Basic accuracy including linearity tolerance : +/- 6dB
Zero offset and rollover +/- 9 digits
Sensor: Logarithmic periodic antenna
Audio Analysis: acoustic signal proportional to the field strength with «Geiger-counter-effect»
Stromversorgung: 9 Volt Alkaline manganese battery (included)
avarage operation time 10 – 12 hours
Low Batt. Indication
Auto-power-off
Signal Rating: peak value
Further Questions: 2 years warranty
Weight: 450 g#
RF-Analyser HF32D
for an easy evaluation of the HF exposure.

This is the device for technical amateurs – especially easy to operate. It allows a straight forward assessment of the exposure, a determination of suitable remedial actions, as well as a control of their effectiveness.

Even this starter device already combines all common advantages.

* The reading shows the total pollution without any calculation required.
* The measured values are reliably displayed directly in the entity corresponding to the building biology standard values.
* An acoustic signal proportional to the field strength with Geiger-counter-effect helps identifying regions with increased exposure.
* Digital display of 1 µW/m² up to 1999 µW/m².

kr 400 Add to my Cart
Utleie av HF Analyzer  HF 58 B -r (per uke)
Utleie av HF Analyzer HF 58 B -r (per uke)

HF/RF-Analyzer HF58B-r
RADAR-/Crest-optimised version of the HF58B

The radar module sets standards in this category of devices. Its functions and features are tailored to the needs and practical experiences of the building biology. Due to its comparably low price, it is often also used for scientific and industrial purposes, especially in the cell phone and wireless sector.

In addition to the full functionality of the HF58B:

* A switch for 2 MHz video bandwidth, allowing especially precise measurements, also of ultra short RADAR signals within the frequency range subject to measurement with a minimum pulse length of up to 0.5 micro seconds, as well as of UMTS-FDD/3G
* Especially high speed of response in the operational mode «peak hold» (patented)

* Technical Data

Frequency Range: 800 MHz – 2.5 GHz (3.3 GHz with increased tolerance)
Measurement Range: Power flux density: 0.01 – 19,990 uW/m²
Accuracy: Basic accuracy including linearity tolerance : +/- 4.5dB
Zero offset and rollover +/- 7 digits
Sensor: Optimised logarithmic periodic antenna: Less ripple, better directionality, improved shielding vs. Ground, continous LED-monitoring of quality of connections
Audio Analysis: Identification of pulsed radiation sources (mobile radio (GSM, UMTS/G3), cordless telephones (DECT), WLAN (Bluetooth), air-traffic control-radar) by means of an acoustic signal proportional to the modulation frequency
Stromversorgung: Recharchable highpower 9.6 Volt NiMH batterypack inside the meter
Average operation time: 7 – 8 hours
Low Batt. Indication
Auto-power-off
AC-adaptor for charging and long-term-operation included
Signal Rating: Display of peak value, peak hold as well as average value (switchable)
A quantitative differentiation between pulsed and un-pulsed radiation – a unique feature within the broadband measuring technology
Outputs: An AC- and a DC-output (AC: demodulated signal)
Weight: 1620 g

kr 1 600 Add to my Cart
Utleie av HF Analyzer  HF 58 B -r (per uke)
Utleie av HF Analyzer HF 58 B -r (per uke)

HF/RF-Analyzer HF58B-r
RADAR-/Crest-optimised version of the HF58B

The radar module sets standards in this category of devices. Its functions and features are tailored to the needs and practical experiences of the building biology. Due to its comparably low price, it is often also used for scientific and industrial purposes, especially in the cell phone and wireless sector.

In addition to the full functionality of the HF58B:

* A switch for 2 MHz video bandwidth, allowing especially precise measurements, also of ultra short RADAR signals within the frequency range subject to measurement with a minimum pulse length of up to 0.5 micro seconds, as well as of UMTS-FDD/3G
* Especially high speed of response in the operational mode «peak hold» (patented)
* Technical Data

Frequency Range: 800 MHz – 2.5 GHz (3.3 GHz with increased tolerance)
Measurement Range: Power flux density: 0.01 – 19,990 uW/m²
Accuracy: Basic accuracy including linearity tolerance : +/- 4.5dB
Zero offset and rollover +/- 7 digits
Sensor: Optimised logarithmic periodic antenna: Less ripple, better directionality, improved shielding vs. Ground, continous LED-monitoring of quality of connections
Audio Analysis: Identification of pulsed radiation sources (mobile radio (GSM, UMTS/G3), cordless telephones (DECT), WLAN (Bluetooth), air-traffic control-radar) by means of an acoustic signal proportional to the modulation frequency
Stromversorgung: Recharchable highpower 9.6 Volt NiMH batterypack inside the meter
Average operation time: 7 – 8 hours
Low Batt. Indication
Auto-power-off
AC-adaptor for charging and long-term-operation included
Signal Rating: Display of peak value, peak hold as well as average value (switchable)
A quantitative differentiation between pulsed and un-pulsed radiation – a unique feature within the broadband measuring technology
Outputs: An AC- and a DC-output (AC: demodulated signal)
Weight: 1620 g#
RF-Analyser HF58B-r
RADAR-/Crest-optimised version of the HF58B.

The radar module sets standards in this category of devices. Its functions and features are tailored to the needs and practical experiences of the building biology. Due to its comparably low price, it is often also used for scientific and industrial purposes, especially in the cell phone and wireless sector.

In addition to the full functionality of the HF58B:

* A switch for 2 MHz video bandwidth, allowing especially precise measurements, also of ultra short RADAR signals within the frequency range subject to measurement with a minimum pulse length of up to 0.5 micro seconds, as well as of UMTS-FDD/3G.
* Especially high speed of response in the operational mode peak hold (patented).

kr 1 600 Add to my Cart
Utleie av HF Analyzer  HF 59 B (per uke)
Utleie av HF Analyzer HF 59 B (per uke)

HF/RF-Analyzer HF59B
Our first class HF-device

Due to its extra broad frequency response, this basic device is predestined for an extension with the UBB27 and for detailed, professional analyses. Its functions and features are tailored to the needs and practical experiences of the building biology. Due to its comparably low price, it is often also used for scientific and industrial purposes – mostly as kit called HF E 59B -, especially in the sector of EMVU and product development (precompliance).

In addition to the full functionality of the HF58B-r:

* A frequency range of down to 27 MHz within the basic device – suitable for the connection of the optionally available antenna UBB27_G3 (the scope of delivery includes a compensated antenna for 800 MHz up to 2.5 or 3.3 GHz)
* A calibrated extra AC-measurement output for the demodulated signal, and a scalable DC-output.
* HINT: If you only need to measure above 800 MHz the HF58B-r is the cheaper and better solution for you. Only with the antenna UBB27 (included e.g. in the kit HFE59B) you can in fact measure frequencies below 800 MHz (e.g. digital TV, TETRA, new GSM Channels in Europe)
* Technical Data

Frequency Range: A frequency range of down to 27 MHz within the basic device – suitable for the connection of an optionally available antenna (the scope of delivery includes a compensated antenna for 800 MHz up to 2.5 or 3.3 GHz)
Measurement Range: Power flux density: 0.01 – 19,990 uW/m²
Accuracy: Basic accuracy including linearity tolerance : +/- 3dB
Zero offset and rollover +/- 5 digits
Sensor: Optimised logarithmic periodic antenna with frequeny compensation directly on the antenna: Less ripple, better directionality, improved shielding vs. Ground, continous LED-monitoring of quality of connections
Audio Analysis: Identification of pulsed radiation sources (mobile radio (GSM, UMTS/G3), cordless telephones (DECT), WLAN (Bluetooth), air-traffic control-radar) by means of an acoustic signal proportional to the modulation frequency
Stromversorgung: Recharchable highpower 9.6 Volt NiMH batterypack inside the meter
Average operation time: 7 – 8 hours
Low Batt. Indication
Auto-power-off
AC-adaptor for charging and long-term-operation included
Signal Rating: Display of peak value, peak hold as well as average value (switchable)
A quantitative differentiation between pulsed and un-pulsed radiation – a unique feature within the broadband measuring technology
Outputs: A calibrated extra AC-measurement output for the demodulated signal, and a DC-output
Further Questions: 2 years warranty
Weight: 820 g#
RF-Analyser HF59B
Our first class HF-device.

Due to its extra broad frequency response, this basic device is predestined for an extension with the UBB27 and for detailed, professional analyses. Its functions and features are tailored to the needs and practical experiences of the building biology. Due to its comparably low price, it is often also used for scientific and industrial purposes – mostly as kit called HF E 59B – especially in the sector of EMVU and product development (precompliance).

In addition to the full functionality of the HF58B-r:

* A frequency range of down to 27 MHz within the basic device – suitable for the connection of the optionally available antenna UBB27_G3 (the scope of delivery includes a compensated antenna for 800 MHz up to 2.5 or 3.3 GHz).
* A calibrated extra AC-measurement output for the demodulated signal, and a scalable DC-output.
* HINT: If you only need to measure above 800 MHz the HF58B-r is the cheaper and better solution for you. Only with the antenna UBB27 (included in the kit HFE59B) you can in fact measure frequencies below 800 MHz (e.g. digital TV, TETRA, new GSM Channels in Europe).

kr 1 800 Add to my Cart