Beskrivelse
HF Isotrop antenne UBB 2410 Istrop Ultra Bredband antenne
kr 3 450
Soon available HF Isotrop antenne UBB 2410 Istrop Ultra Bredband antenne
På lager
HF Isotrop antenne UBB 2410 Istrop Ultra Bredband antenne
Enkelt stativ (av tre) for å kunne gjennomføre potensialfri måling av lavfrekvente elektriske feltLF-Analyser ME3851A
for professional LF analysis
This device represents the low cost access to the professional, quantitative low frequencymeasurement technology. It is suitable for measurement certificates,
comprises all features of the ME3840B, however additionally offers:
* Responsivity increased by a factor of 10 (display range: 0.1 V/m to 0.1 nT)
* A NiMH battery, a battery charger and a power supply unit inclusive
* An AC- and a DC-output
* Increased reliability by the use of a test switching mode for the zero deviation
* Perfectly suitable also for potential-free measurements with the help of the potentialfree mounting for LF measurement devices
* Technical Data
Frequency Range: 5 Hz bis 100 KHz (compensated, better than -2 dB).
Measurement Range: 1-2000 nT V/m
0,1-200 nT V/m
Accuracy: precision : +/- 2 %, +/- 7 digits
Sensor: E-Fieldsensor for electrical LF- fields
H-Fieldsensor for magnetic LF-fields
Audio Analysis: An acoustic signal proportional to the field strength with ? Geiger-counter-effect? helps
identifying regions with increased exposure.
Stromversorgung: recharchable NiMH battery inside the meter
Outputs: AC- and a DC-output
Further Questions: 2 years warranty
Weight: 1050 g
High-pass filter suitable for: HFE35C, HF59B, HFE59B.#
The HP800 increases the measuring accuracy when measuring with the log.-per. antenna in combination with the extremely broad band devices HFE35C and HF59B(Filter included in the scope of supply of the HFE59B).
Why?
The log.-per. antennae are sensitive also for individual frequencies below the specified frequency range. These can be successfully suppressed with the filter, which in turn allows a significantly improved analysis of the measurements with a log.-per. antenna, as the measurements are not impaired by unidentified interference signals.
– This filter helps suppress the lower frequencies. It reaches an attenuation of more than 50 dB (= factor 100,000) below 600 MHz.
– All Gigahertz analysers specified above 800 MHz already come with a similar filter integrated in the basic device. This integration naturally makes no sense for the HFE-types.
– Adaptor plug to be connected to the antenna input socket.
Technical data:
– Accuracy: Attenuation: 10 MHz – 600 MHz < – 50 dB
– Pass band: 0 Hz, 800 MHz – 3000 MHz = -1 dB +/- 0.5 dB
– Return loss: > 12 dB
– Further Questions: Two years warranty
– Weight: 0,03 kg
Scope of delivery:
– High-pass filter
– tightening aid
– manual
RF-preamplifier suitable for: HF58B, HF58B-r, Hf59B.#
Increases the sensitivity of the HF-analyser by a factor of 1000 (= 30 dB). Adaptor plug to be connected to the antenna input socket, remote-fed by the respective basic device.
Further Questions: Two years warranty
Weight: 0,03 kg
Scope of delivery:
– Amplifier
– tightening aid
– manual
FF3 er et bånpass filter tilpasset instrumentene HF35C og HF38B. Med dette filteret er det enkelt å finne hvilke strålingskilder som er dominerende. Ved hjelp av en glidebryter velger du den kilden du er interessert i (f. eks. DECT) og avleser på instrume.
Til HF 35 C, HF 38 B, HF 58 B, HF 59 B.
#Service-specific frequency filter FF3 Recommended for: HF35C, HF38B. The service specific filters always only show the preset radio service, and suppress all other frequencies.
Evaluates each radio service separately
* To be connected between the antenna cable and the antenna input socket of the measurement device (by the operator).
* Cascadable with all amplifiers and attenuators.
* Also allows a broadband measurement without additional transmission loss, which means the filter can remain attached to the measurement device.
* Comprises the most common sources of radiation.Very good selection of the chosen radio services.
* Possible exposures to sheath currents on the cable behind the filter can be additionally suppressed with the help of a free of charge modification of your HF-device. Please do not hesitate to contact us.
Frequency Range: ALL / GSM9 / GSM18 / DECT / UMTS / WLAN
Accuracy: Typical suppression of unwanted frequencies : > 25-30 dB, GSM1800 vs. DECT eff. 20-30 dB.
Power supply: 9 V battery
Attenuator DG20
suitable for: HF32D, HF35C, HF38B
Allows a measurement of major exposures.
For high exposures
– Reduces the sensitivity of the measuring device by a factor of 100 (= 20 dB).
– Adaptor plug to be connected to the antenna input socket.
Weight: 0,06 kg
Silicone hylster til 3D, LF(ME) og HF seriene med instrumenter. Gir en god støtbeskyttelse for instrumentet ditt!
Farve: sort
Variable frequency filter (trap) VF2
convenient for any HF-Analyser from HF35C. For what-if analysis prior to shielding measures
* This filter allows the HF-Series of meters to determine the dominating frequency of the total pollution by suppressing the signal in question by a factor 100 (= 20 dB)
* Full text is currently only available in German
Plastic Transport Case K2 fits one HF and one LF device of any type.
Universal transport case with shaped foam filler inserts
Dimensions: approx. 33 x 27 x 16 cm.
Weight: 0,95kg
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.