Beskrivelse
Sonde for potensialfri måling med NFA serien (TCO-standard)
Sonde for potensialfri måling med NFA serien (TCO-standard)
kr 1 960
TCO 3 sonde for potensialfri måling etter TCO standarden – spesialmodell for NFA serien.
Dette er en rimelig måte å sikre at en kan måle etter TCO standarden for lavfrekvente elektriske felt. TCO 3 benyttes sammen med de professjonelle LF måleapparatene av NFA serien.#TCO-compliant probe for the NFA series TCO3
* For measurements of E-fields in line with the regulations at locations of difficult access, such as bedroom measurements or low-field electrical installation inspections.
På lager
Related Products
KAL-NF Kalibreringssertifikat
Kalibreringssertifikat for ditt måleinstrument. Din dokumentasjon på instrumentets nøyaktighetLF-Analyser ME3851A
for professional LF analysis
This device represents the low cost access to the professional, quantitative low frequencymeasurement technology. It is suitable for measurement certificates,
comprises all features of the ME3840B, however additionally offers:
* Responsivity increased by a factor of 10 (display range: 0.1 V/m to 0.1 nT)
* A NiMH battery, a battery charger and a power supply unit inclusive
* An AC- and a DC-output
* Increased reliability by the use of a test switching mode for the zero deviation
* Perfectly suitable also for potential-free measurements with the help of the potentialfree mounting for LF measurement devices
* Technical Data
Frequency Range: 5 Hz bis 100 KHz (compensated, better than -2 dB).
Measurement Range: 1-2000 nT V/m
0,1-200 nT V/m
Accuracy: precision : +/- 2 %, +/- 7 digits
Sensor: E-Fieldsensor for electrical LF- fields
H-Fieldsensor for magnetic LF-fields
Audio Analysis: An acoustic signal proportional to the field strength with ? Geiger-counter-effect? helps
identifying regions with increased exposure.
Stromversorgung: recharchable NiMH battery inside the meter
Outputs: AC- and a DC-output
Further Questions: 2 years warranty
Weight: 1050 g
STS 1 Elektrostatiksensor
Måleinstrumenet for å måle elektrostatisk oppladning på f. eks. bildeskjermer, teppegulv etc. Slik oppladning påvirker lufkvalitet etc.
Måleområder: 2000V og 20 KVLF-Analyser ME3851A
for professional LF analysis
This device represents the low cost access to the professional, quantitative low frequencymeasurement technology. It is suitable for measurement certificates,
comprises all features of the ME3840B, however additionally offers:
* Responsivity increased by a factor of 10 (display range: 0.1 V/m to 0.1 nT)
* A NiMH battery, a battery charger and a power supply unit inclusive
* An AC- and a DC-output
* Increased reliability by the use of a test switching mode for the zero deviation
* Perfectly suitable also for potential-free measurements with the help of the potentialfree mounting for LF measurement devices
* Technical Data
Frequency Range: 5 Hz bis 100 KHz (compensated, better than -2 dB).
Measurement Range: 1-2000 nT V/m
0,1-200 nT V/m
Accuracy: precision : +/- 2 %, +/- 7 digits
Sensor: E-Fieldsensor for electrical LF- fields
H-Fieldsensor for magnetic LF-fields
Audio Analysis: An acoustic signal proportional to the field strength with ? Geiger-counter-effect? helps
identifying regions with increased exposure.
Stromversorgung: recharchable NiMH battery inside the meter
Outputs: AC- and a DC-output
Further Questions: 2 years warranty
Weight: 1050 g
Multifunksjons-sensor MFP
Enkel spenningstester, ser ut som en skrutrekker#Zur Überprüfung des phasenrichtigen Anschlusses von Elektrogeräten.
Høypass filter HP800_G3
High-pass filter suitable for: HFE35C, HF59B, HFE59B.#
The HP800 increases the measuring accuracy when measuring with the log.-per. antenna in combination with the extremely broad band devices HFE35C and HF59B(Filter included in the scope of supply of the HFE59B).
Why?
The log.-per. antennae are sensitive also for individual frequencies below the specified frequency range. These can be successfully suppressed with the filter, which in turn allows a significantly improved analysis of the measurements with a log.-per. antenna, as the measurements are not impaired by unidentified interference signals.
– This filter helps suppress the lower frequencies. It reaches an attenuation of more than 50 dB (= factor 100,000) below 600 MHz.
– All Gigahertz analysers specified above 800 MHz already come with a similar filter integrated in the basic device. This integration naturally makes no sense for the HFE-types.
– Adaptor plug to be connected to the antenna input socket.
Technical data:
– Accuracy: Attenuation: 10 MHz – 600 MHz < – 50 dB
– Pass band: 0 Hz, 800 MHz – 3000 MHz = -1 dB +/- 0.5 dB
– Return loss: > 12 dB
– Further Questions: Two years warranty
– Weight: 0,03 kg
Scope of delivery:
– High-pass filter
– tightening aid
– manual
Peil-Antenne LAT 10
Peileantenne, tilbehør til HF måleinstrumenter. Gjør det enklere å bestemme nøyaktig posisjon for strenderantenner. Denne peileantennen har langt mindre åpningsvinkel enn de vanlige, også direktive LogPer antennene.
VF 2 Variabelt Frekvensfilter – for å finne strålingskilden
Variable frequency filter (trap) VF2
convenient for any HF-Analyser from HF35C. For what-if analysis prior to shielding measures
* This filter allows the HF-Series of meters to determine the dominating frequency of the total pollution by suppressing the signal in question by a factor 100 (= 20 dB)
* Full text is currently only available in German
Jord-sjekk for stikkontakten
Enkel plugg som ved hjelp av lys forteller deg om jord er som den skal være i en stikkontakt. Bare brukelig i jordede uttak, kun tilpasset 400V distribusjon.