Beskrivelse
Spectran USB Cable
To connect your Spectran to the PC.
Special version with high performance EMC-ferrite.
Length: 1m.
Fits to all Spectran Spectrum Analyzer.
Strongly recommended for PC use.
USB kabel for Spectrum Analysator
kr 200
USB kabel for Spectrum Analysator
På lager
Related Products
Frekvensfilter FF6
FF6 er et lav- høy- og bånpass filter anbefalt for HF58B og HF58B-r. Med dette filteret er det enkelt å finne hvilke strålingskilder som er dominerende. Ved hjelp av en glidebryter velger du den kilden du er interessert i (f. eks. DECT) og avleser på inst.
# Med dette filteret er det enkelt å finne hvilke strålingskilder som er dominerende. Ved hjelp av en glidebryter velger du den kilden du er interessert i (f. eks. DECT) og avleser på instrumentet direkte verdien for denne strålingskilden.>Måler lavpass, høypass (1,1 GHz), GSM900, GSM1800, DECT,UMTS og WLAN.
Info Engl.
Evaluates each radio service separately
Additional features as compared to the FF3:
* The 50-60 dB suppression of unwanted frequencies is unequalled in this product segment. It allows for a precise analysis of the selected frequency ranges.
* An additional high pass filter applied at 1100 MHz helps differentiating in areas with high levels in the TV bands.
* To be connected between the antenna cable and the antenna input socket of the measuring device (by the operator).
* Cascadable with all amplifiers and attenuators.
* Also allows for a broadband measurement without additional transmission loss, which means the filter can remain attached to the device.
* Perfectly shielded against interferences.
* Possible exposures to sheath currents on the cable behind the filter can be additionally suppressed with the help of a free of charge modification of your HF-device.
Dirty electricity Pakke 5 (20 filtere)
Skittenstrømfilterene demper støy fre det elektriske anlegget ved at den fjerner uheldige frekvenser som rir på de rene sinusfrekvensene i strømnettet. Det er særlig sparepærer, lysstoffrør og alt av elektronisk utstyr som lager disse frekvensene. Skittenstrømen måles med en skittenstrømmonitor som puttes i vegguttaket. Man legger til filtere i den sammme kretsen til den ønskede effekten er oppnådd.
NFA 1000 (LH Analyzer, 3D, datalogg, proff)
Ekte 3D potensialfri måling av elektriske felt. Utvidet frekvensanalyse basert på optimalisert FFT opp til 32 KHz og bredbåndsverdier over 32 KHz. Du kan velge ekte peak målinger i bredbåndsområde. Opsjon: Integrert transientopptaker opp til 1 MHZ med mange timers opptak. Ta en kikk på Gigahertz sine sider for full oversikt! www.nfa-meters.com
An innovative step forward in the scope of LF analysis: The NFA 1000 is both, a precise 3D magnetic field logger as well as a high-resolution potential-free E-field cube, all in one meter among the professional devices (patented technology) supported by the comforting certainty of having the complete technical expertise of Gigahertz Solutions behind it.
The essence of all devices is a high-capacity processor able to analyze the field situation with an axe-specific FFT and a sampling rate of 110,000 data records per second, and to record all data on a standard SD-card. It is furthermore possible to connect external probes, and to simultaneously record the corresponding measurement values (available for high frequency and for static fields).
The easy to operate PC program NFAsoft with its revolutionary statistical functions as well as evaluation functions provides a quick overview and if necessary an analysis down to the last detail.
3D-LF-Analyser with data logger NFA 1000 for the most in-depth analysis – our masterpiece! Innovative alternative to the ME series based on a superior concept for efficient data acquisition of electric and magnetic fields, extensive long-term recordings of all relevant parameters and facilitated interpretation and documentation of the acquired data. Features: * Real 3D potential-free electric field measurement, patent pending. * 3D measurement of the magnetic field in a truly isotropic point. * Separate recordings of railway and grid frequencies as well as higher harmonics with true RMS valuation (16.6 Hz | 50/60 Hz | 100/120 Hz plus even harmonics | 150/180 Hz plus uneven harmonics | other frequencies < 2 kHz | all > 2kHz) * Measures 110,000 samples per second, the maxima of which are recorded up to 10 times per second on the 4 GB SDHC memory card supplied. Due to the simultaneous and continuous sampling of frequency and axis information you won’t miss even the smallest peaks. * Voice recording of audio notes to facilitate measurement and interpretation of recordings. * Broadband peak measurements (genuine peak of a wave) as a firmware update in preparation. * Optional, in preparation: Wireless data transfer to external display unit /PC. * Supplied with revolutionary PC evaluation software: Super fast real-time presentation, statistic functions (e.g. 95. percentile), analysis tool for Dirty Power. * Li-Ion rechargeable batteries for up to 48 hours of continuous recordings. External power supply possible (power adapter included).
Frekvensfilter FF3
FF3 er et bånpass filter tilpasset instrumentene HF35C og HF38B. Med dette filteret er det enkelt å finne hvilke strålingskilder som er dominerende. Ved hjelp av en glidebryter velger du den kilden du er interessert i (f. eks. DECT) og avleser på instrume.
Til HF 35 C, HF 38 B, HF 58 B, HF 59 B.
#Service-specific frequency filter FF3 Recommended for: HF35C, HF38B. The service specific filters always only show the preset radio service, and suppress all other frequencies.
Evaluates each radio service separately
* To be connected between the antenna cable and the antenna input socket of the measurement device (by the operator).
* Cascadable with all amplifiers and attenuators.
* Also allows a broadband measurement without additional transmission loss, which means the filter can remain attached to the measurement device.
* Comprises the most common sources of radiation.Very good selection of the chosen radio services.
* Possible exposures to sheath currents on the cable behind the filter can be additionally suppressed with the help of a free of charge modification of your HF-device. Please do not hesitate to contact us.
Frequency Range: ALL / GSM9 / GSM18 / DECT / UMTS / WLAN
Accuracy: Typical suppression of unwanted frequencies : > 25-30 dB, GSM1800 vs. DECT eff. 20-30 dB.
Power supply: 9 V battery
HF Analyzer HF 38 B (Måler høyfrekvens)
Dette er linken mellom amatør og profesjonelle måleapparater. Dette er apparatet for leger og alternative praktikere.Den har alle de samme funksjonene som 35C men en høyere respons og sensibilitet.
# This device supports all above mentioned “common advantages”. It is especially popular among medics and alternative practitioners, as it offers a perfect combination of easy handling and professional measurement possibilities. It allows an easy allocation of the electrosmog frequencies to the traction power or the mains power as well as to the artificial harmonics, thus facilitating an especially precise consultation of remedial actions and an easy control of their effectiveness.
Has the same features and configuration as the HF35C, however additionally offers some important professional features:
– The log.-per. antenna with further improved frequency response.
– A 10 times higher sensitivity: Minimum display resolution 0.01 µW/m² .
– A measuring range extended upwards by a factor of 10: max. 19.99 mW/m² .
– Clearly simplified measurements with the help of the “peak-hold”- function.
Technical Data:
Frequency Range: 800 MHz – 2.5 GHz (3.3 GHz with increased tolerance)
Measurement Range: Power flux density: 0.01 – 19,990 µW/m²
Accuracy: Basic accuracy including linearity tolerance : +/- 6dB
Zero offset and rollover +/- 9 digits
Sensor: Optimised logarithmic periodic antenna: Less ripple, better directionality, improved shielding vs. ground
Audio Analysis: Identification of pulsed radiation sources (mobile radio (GSM, UMTS/G3), cordless telephones (DECT), WLAN (Bluetooth), air-traffic control radar) by means of an acoustic signal proportional to the modulation frequency
Electric power supply: 9 Volt alkaline manganese battery (included), average operation time 6 – 7 hours
Low-Batt. indication, auto-power-off
Signal Rating: Display of peak value, peak hold as well as average value (switchable)
Further Questions: 2 years warranty & long-time ex gratia agreement
Weight: 0,58 kg
Dirty electricity Pakke 3 (10filtere + 1 monitor)
Skittenstrømfilterene demper støy fre det elektriske anlegget ved at den fjerner uheldige frekvenser som rir på de rene sinusfrekvensene i strømnettet. Det er særlig sparepærer, lysstoffrør og alt av elektronisk utstyr som lager disse frekvensene. Skittenstrømen måles med en skittenstrømmonitor som puttes i vegguttaket. Man legger til filtere i den sammme kretsen til den ønskede effekten er oppnådd.
HF Analyzer HF 35C (Måler høyfrekvens)
Dette er apparatet for de tekniske
amatører. Apparaet gir en enkel evaluering av høyfrekvent stråling, og
har en audiofunksjon som gjør at man kan høre strålingsmengden.
Apparatet gir og en visning av toppverdier i tillegg til
gjennomnittsverdier.#
This is THE device for technical amateurs –
especially easy to operate. It allows a straight forward assessment of
the exposure, a determination of suitable remedial actions, as well as a
control of their effectiveness.
Even this starter device already
combines all common advantages. The reading shows the total pollution
without any calculation required. The measured values are reliably
displayed directly in the entity corresponding to the building biology
standard values. An acoustic signal proportional to the field strength
with “Geiger-counter-effect” helps identifying regions with increased
exposure. Digital display of 1 µW/m2 up to 1999 µW/m2.
Frequency Range: 800 MHz – 2.5 GHz
Measurement Range: Power flux density: 1 – 1999 µW/m2
Accuracy: Basic accuracy including linearity tolerance : +/- 6dB Zero offset and rollover +/- 9 digits
Sensor: Logarithmic periodic antenna
Audio Analysis: acoustic signal proportional to the field strength with “Geiger-counter-effect”
Signal rating: peak value
Power
supply: 9 Volt alkaline manganese battery (included), average operation
time 10 – 12 hours Low-Batt. indication, auto-power-off
LF Analyzer ME 3840 B (Måler lavfrekvens, med filter)
LF Analyzer ME 3840 B (Måler lavfrekvens, med filter)